 |
 |
 |
 |
|
Product Detail |
 |
Features
Novak GTB/SS 10.5 Pro Brushless System 3010
Brushless Motors Features
SS10.5 Brushless Motor (NOVC3410);
Sensor based design for excellent starting torque, continuous synchronization, low-speed driveability, consistent brakes and thermal protection
Provides approximately 20% longer run-times than brushed motors
One-piece design neodymium magnets provide high power and great reliability
Nickel plated sintered neodymium rotor
User-replaceable rotor, front end bell/bearing, and rear bearing
Convenient solder tab system for easy wire replacement
Thermal Overload Protection (when used with a Novak brushless ESC)
Non-removable color timing ring
Lightweight ribbed aluminum end bells
ESC Features
Novak GTB Programmable Electronic Speed Control (NOVM1710);
Four different color status LEDs for easy set-up, programming and profile selection
3 fully-programmable fwd/brake/ Brushless profiles
1 fully-programmable fwd/brake/ Brush motor profile
1 fully-programmable fwd/brake/rev Brushless motor profile
1 fixed-programming Limited Reverse (25%) profile
Programming adjustments include; Min Drive, Min Brake, Drag Brake &
Dead Band, Drive Frequency adjustable in the Brush-Mode
Low profile high volume cooling fan and factory team Power Trans-Cap Module
Gold plated PCB direct-solder tabs and 6-layer circuit boards for lowest possible voltage drop and easy power wire replacement
User replaceable input harness, long and short input harnesses supplied
Remote power programming switch combines one-touch button and ON/OFF switch, can be remotely mounted for easy programming adjustments and powering ESC ON and OFF
Water-resistant case with complete gasketing for improved protection
120 day limited warranty on both components
Motor Specifications
SS10.5 Brushless Motor
Turns: 10.5
Design: Sensor-based
Motor Size: 540 Size: 2.08" L x 1.41" D (52.8 x 35.8mm)
Weight: 6.61 oz. (187 grams)
Input Voltage: 4-7 cells (1.2V/cell or 4.8-8.4 total volts)
Magnet: Nickel-plated, Sintered, high-strength Neodymium
Watts: 235
KV (unloaded): 4200
Shaft Diameter: 0.125" 3.2mm (accepts all existing pinion gears)
Front Bearing Size: 1/2 x 3/16" (12.7 x 4.8mm)
Protection: Thermal
GTB Programmable Electronic Speed Control
Size: L 1.49" (37.8mm), W 1.16" (29.5mm)
Weight: 1.36oz (38.5g) without wires
BEC: 6.0V/3.0A
Input Voltage: 4-6 cells (1.2VDC/cell)
*On Resistance (Brushless): 0.00040 ohms
*On Resistance (Brush Mode): 0.00013 ohms
*Rated Current (Brushless): 540A/phase
*Rated Current (Brush Mode): 1620A
Battery/Motor Wire:14AWG silicone
Throttle Profiles: 6 (5 Brushless/1 Brush)
Drive Frequencies: 1 of 7 (1.5-11kHz)
Minimum Drive: 1 of 5 (2-12%)
Minimum Brake: 1 of 10 (5-50%)
Dead Band: 1 of 5 (2-6%)
Braking Style: Std or Drag Brake
Drag Brake: 1 of 10 (10-50%)
Brushless Motor Limit: Any Novak
Brushed Motor Limit: None
*Transistor rating @ 25°C junction temp
Contents
Novak GTB Programmable Electronic Speed Control with Factory Installed Power Wires and Power Trans Cap Module, User-Replaceable Remote Power Programming Switch and Input Harness (two lengths included), Instructions, double Sided Tape SS10.5 Brushless Motor
Requirements
Installing in vehicle
|
|
 |
 |
|
|
|
 |
 |
 |
